Excellent Sterling Silver Rectangle Wire,Hollow Rubber Tube, and Turquoise Earrings(jewelry tutorial)




Sterling Silver Crescent and Bead Earrings

Supplies NEEDED
3" 4 x 1 mm sterling silver rectangle wire
20-a person 'Λ* head pins
Two turquoise disc beads
One Vi* 1.7 mm black hollow rubber tube
Two sterling silver ear wires
What tips would you give a commencing artist?
“Do what you enjoy. Investigate distinct media. Market over a selective, confined, basis initially to find out what performs or what won't be just right for you before you jump into a major outlay of money and effort.*
-Sally J. Phillips Jewelry Designer
Equipment Desired
Ruler
Marker
Jeweler's saw or tin snips Safety glasses Challenging, flat area Awl
Hammer /is" drill little bit
Hand-held rotary Software, flex shaft, or drill press File
Fine grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Scissors
Wire cutters or tin snips Round nose pliers


1.Use the ruler to measure and mark two 1 Vi’ pieces of 4 x 1 mm rectangle sterling silver wire.
2Using a jeweler's noticed or tin snips, Lower the four x one mm rectangle sterling silver wire into two one Vi’ lengths.
three.File Just about every end in the 1Vi" rectangle wire items to get rid of any burs or tough edges.
If ideal, You may use the file to around the finishes of your rectangle wire pieces. Use a fine grit sanding pad to go more than the area where you have filed to smooth the edges and remove any file marks.
four.Make use of the ruler to evaluate and mark /*." from just one conclusion of your one Vi’ parts of rectangle wire and position a mark in the middle with the wire. This is when you may drill the holes to slip The top pins by means of.
5.Place in your security glasses!!! Location the 1 Vi" rectangle wire pieces on to a tough, flat area. Position The purpose with the awl to the mark that you just manufactured Vm,' from one particular conclude in the rectangle wire items, and firmly strike when on the very best from the awl with a hammer. This will make a pilot gap for drilling holes into your rectangle wire.

Sterling Silver Crescent and Bead Earrings
Chapter five

six.Utilizing a /is" drill bit. drill holes into 1 end of the rectangle wire parts that has a handheld rotary Resource, flex shaft, or drill push (although nevertheless sporting your safety Eyeglasses!).
seven.Make use of the file or fantastic grit sanding pad to eradicate any burs or rough edges left mens ring from drilling holes into your rectangle wire parts.
8.Curve the two 1W pieces of rectangle wire right into a “C" condition employing a ring mandrel and rawhide mallet. If you Mens Ring don't have a ring mandrel and rawhide mallet, use two pair of chain nose pliers. mens ring Keeping just one pair of pliers in Each and every hand, grasp Every end Mens Ring with the 1 Vi* rectangle wire piece With all the pliers and gently bend the rectangle wire right into a “C* form. Examine each of the C-formed rectangle wire items and alter the curves so that they are identical in si2e. Established these aside.
nine.Utilize the ruler to measure and mark the rubber tube into four equivalent items measuring Vm’ Each and every. Use scissors to cut the rubber tube.
ten.Area the turquoise disc bead onto The pinnacle pin and insert a single V·' piece of the rubber tube, put The top pin with the hole from the C-shaped rectangle wire, and after that add the opposite V«" piece of rubber tube.

13. Keep The top pin Using the bead, rubber tube, as well as rectangle wire on it in a single hand Using the wire that you bent pointing towards you. Using the spherical nose pliers, grip the tip of the head pin wire that is pointing towards you and roll it far from you (think of turning the ignition critical to begin your car). Launch the pliers from the head pin wire.
At this stage, the opening while in the loop at the top of The pinnacle pin wire must nonetheless be significant ample to slip the ear wire on. When you include the ear wire, utilize the spherical nose pliers to grasp the loop of the head pin wire and roll it shut. You can utilize the spherical nose or chain nose pliers to regulate the shape with the loop at the very best of The pinnacle pin if you must.
11. Utilize the ruler to measure and mark /(.’ higher than the very best bit of the hollow rubber tube. Together with the wire cutters or tin snips, Reduce The pinnacle pin wire Yu.’ over the best on the hollow rubber tube.
12. Make use of the chain Mens Ring nose pliers to bend the head pin wire beside the top with the rubber tube at a ninety-degree angle.
fourteen. Repeat these measures for the 2nd earring.







 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Excellent Sterling Silver Rectangle Wire,Hollow Rubber Tube, and Turquoise Earrings(jewelry tutorial)”

Leave a Reply

Gravatar